How to film a car for 3DGS: a step-by-step video guide
If you want a good Gaussian splat of a car, the most important moment is not the processing. It is the two or three minutes you spend filming. A 3DGS pipeline can only reconstruct what the camera has seen clearly. This guide explains how to film a car for Gaussian splatting with nothing more than a smartphone, and how to avoid the mistakes that cause blurry, broken or floating results.
Why filming matters so much for 3DGS
Gaussian splatting learns what an object looks like from every angle in your footage. It needs three things from your video:
- Sharp frames, so the software can find matching details between images
- Enough overlap, so every part of the car is seen from several neighbouring angles
- Consistent light, so the same piece of paint looks roughly the same in different frames
Motion blur, gaps in coverage and changing light confuse the camera reconstruction and the training. The result is typically a fuzzy area, "floaters" in the air, or parts of the car that are missing. The good news: all of this is easy to prevent.
Step 1: Prepare the location
Choose a calm environment with plenty of space around the car. You need to be able to walk a full circle at a constant distance, usually two to three metres from the bodywork.
- Avoid other cars and people moving through the shot.
- Prefer overcast weather or even shade. Soft light gives far better results than bright sun.
- Avoid strong reflections on the paint. Low sun, a bright wall right next to the car or a lamp shining on the bonnet create highlights that move as you walk.
- Clean the car. Dirt and water drops are fine for realism, but large wet patches reflect differently from frame to frame.
- Open space under and around the car helps the pipeline recognise the ground.
A spacious car park on a grey day is often better than a beautiful but cramped showroom.
Step 2: Set up your phone
You do not need special apps or settings. A few simple choices help:
- Film in landscape so the whole car fits comfortably in the frame.
- Use the main lens (1x), not the ultra-wide, which distorts edges.
- Film in good quality, 1080p or 4K at a normal frame rate.
- Lock exposure and focus if your phone allows it, so the brightness does not jump.
- Turn off stabilisation effects that crop or warp the image, if you can. Normal stabilisation is fine.
Step 3: Round 1, the overview
Walk once around the car at a normal pace, keeping the whole car in view at all times. Hold your phone at roughly chest height and point it at the centre of the car. Keep the same distance all the way round.
Tips for a clean overview round:
- Walk slowly and smoothly, with small steps. Avoid sudden turns.
- Do not stop and start; a constant pace gives evenly spaced frames.
- Make sure you end where you started, so the circle is closed.
Step 4: Round 2, the details
Walk around the car a second time. This time, move the camera slowly up and down as you go, so you capture the car from lower and higher angles and come a little closer to important details such as wheels, lights, grille and mirrors.
- Lower the camera to around wheel height for the sides and wheels.
- Raise it again to see the bonnet, windscreen and boot lid from above.
- Keep movements slow; the up-and-down motion should feel almost lazy.
- Keep the car (or the part you are focusing on) sharp and well lit.
These two rounds together give the 3DGS training enough different viewpoints to build a convincing model.
Step 5: Check your recording
Before uploading, quickly play back the video:
- Is the car sharp throughout, without motion blur?
- Is it well lit, without harsh shadows or blown-out highlights?
- Did you complete both full rounds?
- Is the car in frame the entire time?
If something looks off, film again. It takes a few minutes and saves you a credit.
Common mistakes when filming for Gaussian splatting
- Walking too fast. The most frequent cause of blur.
- Bright sunlight. Hard reflections move across the paint and appear as artefacts.
- Cutting off part of the car. What the camera never saw cannot be reconstructed.
- Zooming in and out. Changing focal length makes the camera reconstruction harder.
- Too close to the car. If you are so close that only a door fills the frame, the software loses context.
- People or cars moving through the background. Moving objects leave ghost artefacts.
Dark, glossy and chrome surfaces are a special challenge. We explain why in why shiny paint is hard for Gaussian splatting.
What happens after you upload
With CarTwin you upload the video as it is: no compressing, no editing, no frame extraction on your side. Our car-specific pipeline then:
1. Picks the sharpest frames from your video 2. Reconstructs the camera path around the car 3. Trains the Gaussian splat 4. Detects the ground and straightens the car
After roughly 60 to 75 minutes you can view the model in your browser, share a link, or download the .ply. One scan costs one credit; see the pricing for bundles.
CarTwin is still fully in development and in an early pilot phase, so a result is not always a perfect one-to-one copy of the car. If a scan fails because of an error in our software, you get the credit back; a disappointing result on its own is not refunded. Following this guide is the best way to get a result you are happy with.
Quick checklist
- Calm location, lots of space, soft light
- Landscape, main lens, good quality
- Round 1: whole car in view, normal height, steady pace
- Round 2: slowly up and down, closer to details
- Play it back: sharp, well lit, complete
Ready to film your first car?
You now know more about filming for 3DGS than most people who try it for the first time. Read the short recording guide, look at the examples, and start a scan with your next video.
